- Perma-Grout Stain & Seal
- >
- Perma-Grout Stain & Sealer Gallon (128 oz)
Perma-Grout Stain & Sealer Gallon (128 oz)
SKU:
$130.00
$130.00
Unavailable
per item
We match grout colors from the following manufacturers: Mapei, Bonsal, Jamo, SGM, Laticrete, Custom Building Products, All Set, QSet, C-Cure, Hydroment, Flextile, Tec, Aqua Mix. Please consult a color chart and select a brand and color when you place your order.
Coverage: (1000-1500 sq. ft)
Coverage: (1000-1500 sq. ft)
Use on new grout with noticeable shade variations and it also seals it.
Perma-Grout Stain and Seal is a new concept in tile grout joints. Pick a bright new color from an array of exciting designer shades or order a customized color. Perma-Grout Stain and Seal is a tough acrylic water-based stain-and-seal finish that applies easily, dries quickly, and leaves your tile floors or your countertops looking more beautiful than ever before and sealed.
Stain Resistant: So your grout can be cleaned as easily as your tile and stay clean.
Color Fast: So you'll never have to worry about stains or discoloration.
Sturdy: So it will not wear away and leave pits and holes in your grout.
Color Matched: We match grout colors from the following manufacturers: Mapei, Bonsal, Jamo, SGM, Laticrete, Custom Building Products, All Set, QSet, C-Cure, Hydroment, Flextile, Tec, Aqua Mix. Please consult a color chart and select a brand and color when you place your order.
- No digging or scraping out old grout
- Stain resistance
- Color fast
- Sturdy
Perma-Grout Stain and Seal is a new concept in tile grout joints. Pick a bright new color from an array of exciting designer shades or order a customized color. Perma-Grout Stain and Seal is a tough acrylic water-based stain-and-seal finish that applies easily, dries quickly, and leaves your tile floors or your countertops looking more beautiful than ever before and sealed.
Stain Resistant: So your grout can be cleaned as easily as your tile and stay clean.
Color Fast: So you'll never have to worry about stains or discoloration.
Sturdy: So it will not wear away and leave pits and holes in your grout.
Color Matched: We match grout colors from the following manufacturers: Mapei, Bonsal, Jamo, SGM, Laticrete, Custom Building Products, All Set, QSet, C-Cure, Hydroment, Flextile, Tec, Aqua Mix. Please consult a color chart and select a brand and color when you place your order.
Application:
Clean grout joints thoroughly by scrubbing tile and grout with "industrial strength" phosphoric acid.
Mix 1 part cleaner to 4 parts water. Apply liberally to surface leaving on five to ten minutes making sure surface remains wet. Scrub grout and tile with scrub brushes and mop floor or area. (If floor machine is used, grout must still be scrubbed with scrub brushes.) Rinse well with clean water and let dry 2 hours minimum.
Shake or stir Perma-Grout Stain and Seal thoroughly and apply straight out of the container (DO NOT DILUTE). Paint grout joints using clean paint brush (2 to 4 inch brush). Excess, which will get on edge of tiles will be cleaned off later. If desired, let dry 2 hours and apply a second coat. (In most cases a second coat is recommended.) After second coat dries for a minimum of 3 hours, no longer than 24 hours, liberally apply clean water to area where excess stain is to be removed from tiles. Working with an area no larger than 200 square feet at a time, keeping area wet, agitate excess stain using a mop, doodle-bug pad or terry cloth towel depending on area to be removed. Clean up excess stain with mop, towel or wet vac on floors is easiest. Final rinse with clean mop and clean water. Rinse well.
Maintenance:
Maintain your new floor with Choice All Purpose Cleaner specifically developed for Perma-Grout Stain and Seal. Add 1/2 cup of Choice All Purpose Cleaner to 2 gallons of water, mop floor, no rinsing is necessary. Note: It is recommended to use plain water every fourth cleaning or in between regular cleaning. This will rinse the floor and not allow build up of cleaner. Spray bottle for spot cleaning is also recommended. A light scrubbing may be necessary in certain areas (kitchen, hall traffic areas). Use Choice All Purpose Cleaner Only, other cleaning products can strip off stain and cause damage.
Spray Bottle: Add 2 to 4 ounces of Choice All Purpose Cleaner to a quart spray bottle and fill with water. Use for kitchen clean up, shower walls, shower doors, ceramic tile and spot cleaning on Perma-Grout Stain and Seal.
Helpful Hints: Trim paint brush bristles to 1/2" to 1" (inches). This will stiffen brush to assure correct coverage. Do not leave excessive stain on tiles, base boards, etc.
Important:
Before applying Perma-Grout Stain and Seal to entire area, a test should be done to determine satisfaction of color. Color and shade may vary from dye lot to dye lot. If dye lot numbers are different from container to container, mix all containers together to make one container and do a test for color and shade.
Stain dries 3 to 4 shades darker than first applied. A blow drier can be used in a test area to determine final color.
Do not apply at temperatures above 90 degrees or below 50 degrees F.
Clean grout joints thoroughly by scrubbing tile and grout with "industrial strength" phosphoric acid.
Mix 1 part cleaner to 4 parts water. Apply liberally to surface leaving on five to ten minutes making sure surface remains wet. Scrub grout and tile with scrub brushes and mop floor or area. (If floor machine is used, grout must still be scrubbed with scrub brushes.) Rinse well with clean water and let dry 2 hours minimum.
Shake or stir Perma-Grout Stain and Seal thoroughly and apply straight out of the container (DO NOT DILUTE). Paint grout joints using clean paint brush (2 to 4 inch brush). Excess, which will get on edge of tiles will be cleaned off later. If desired, let dry 2 hours and apply a second coat. (In most cases a second coat is recommended.) After second coat dries for a minimum of 3 hours, no longer than 24 hours, liberally apply clean water to area where excess stain is to be removed from tiles. Working with an area no larger than 200 square feet at a time, keeping area wet, agitate excess stain using a mop, doodle-bug pad or terry cloth towel depending on area to be removed. Clean up excess stain with mop, towel or wet vac on floors is easiest. Final rinse with clean mop and clean water. Rinse well.
Maintenance:
Maintain your new floor with Choice All Purpose Cleaner specifically developed for Perma-Grout Stain and Seal. Add 1/2 cup of Choice All Purpose Cleaner to 2 gallons of water, mop floor, no rinsing is necessary. Note: It is recommended to use plain water every fourth cleaning or in between regular cleaning. This will rinse the floor and not allow build up of cleaner. Spray bottle for spot cleaning is also recommended. A light scrubbing may be necessary in certain areas (kitchen, hall traffic areas). Use Choice All Purpose Cleaner Only, other cleaning products can strip off stain and cause damage.
Spray Bottle: Add 2 to 4 ounces of Choice All Purpose Cleaner to a quart spray bottle and fill with water. Use for kitchen clean up, shower walls, shower doors, ceramic tile and spot cleaning on Perma-Grout Stain and Seal.
Helpful Hints: Trim paint brush bristles to 1/2" to 1" (inches). This will stiffen brush to assure correct coverage. Do not leave excessive stain on tiles, base boards, etc.
Important:
Before applying Perma-Grout Stain and Seal to entire area, a test should be done to determine satisfaction of color. Color and shade may vary from dye lot to dye lot. If dye lot numbers are different from container to container, mix all containers together to make one container and do a test for color and shade.
Stain dries 3 to 4 shades darker than first applied. A blow drier can be used in a test area to determine final color.
Do not apply at temperatures above 90 degrees or below 50 degrees F.